收藏本站
NMA 24V & 48V Series
Isolated 1W Dual Output DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Conditions
Flash tested for 1 second
Viso= 500VDC
Min.
1000
10
Typ.
Max.
Units
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
All input types
Min.
Typ.
100
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Conditions
All output types
Min.
0
-55
Typ.
Max.
70
150
Units
°C
Cooling
Free air convection
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination
?nish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate.
Both types in this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMA series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMA series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMA series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
APPLICATION NOTES
Minimum load
The minimum load to meet datasheet speci?cation is 10% of the full rated load across the speci?ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the speci?ed output voltage if the output load falls to less than 5%.
www.murata-ps.com/support
KDC_NMAC2.G02 Page 2 of 4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NMD050505SC CONV DC/DC 1W 5VIN 5-5VOUT SIP
NME0509SC CONV DC/DC 1W 5VIN 9VOUT SIP SGL
NME2412DC CONV DC/DC 1W 24VIN 12V DIP SGL
NMF2405SC CONV DC/DC 1W 24VIN 5V SIP SGL
NMG0512SC CONV DC/DC 2W 5VIN 12VOUT SIP
NMH0524DC CONV DC/DC 2W 5VIN 24VOUT DIP DL
NMH1212DC CONV DC/DC 2W 12VIN 12V DIP DL
NMJ0515SAC CONV DC/DC 1W 5VIN 15V SIP 5.2KV
相关代理商/技术参数
NMA2409D 功能描述:DC/DC转换器 1W DUAL 24V/09V DIP RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMA2409DC 功能描述:DC/DC转换器 24V to +/-9V +/-55mA DIP RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMA2409M 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
NMA2409S 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Isolated 1W Dual Output DC-DC Converters
NMA2409SC 功能描述:DC/DC转换器 24V to +/-9V +/-55mA SIP RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMA-2410 制造商:MICRONETICS 制造商全称:MICRONETICS 功能描述:NOISE MODULES 10 MHZ TO 8.5 GHZ
NMA2410-A2S 制造商:MICRONETICS 制造商全称:MICRONETICS 功能描述:Legacy 10 MHz to 1000 MHz
NMA2410-A2T 制造商:MICRONETICS 制造商全称:MICRONETICS 功能描述:Legacy 10 MHz to 1000 MHz